CPR 804 – Industrial Floor Paint – Epoxy HB – Rapid Cure

Description

Industrial Floor Paint – Epoxy HB – Rapid Cure

CPR 804 – Industrial Floor Paint – Epoxy HB – Rapid Cure is a two-pack Epoxy coating which provides protective and decorative properties to concrete, steel and other substrates. The material is supplied as a two pack system, comprising pre-weighed amounts of BASE and CURING AGENT. After mixing together, an easily applied chemical and abrasion resistant finish is produced with fast curing characteristics.

Typical Properties

• Rapid Cure
• Solvent free, low odour
• Very good chemical resistance
• Excellent adhesion to concrete and steel
• High build
• Tough and durable
• Easily applied
• Hygienic and easily cleaned
• Slip resistant options
• Range of colours available (standard Grey/ Red)

Direction for Use

Surface Preparations Concrete

• Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%.
• Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes, etc.
• Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. CPR 716 Concrete Patch Repair Mortar – Rapid Cure – Epoxy.
• Using a suitable mechanical treatment such as vacuum grit blasting is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating.
• A primer coat of CPR 402 – Concrete Primer – Epoxy WB – Rapid Cure @ 0.2kg/m², is recommended for absorbent concrete surfaces.
• Allow to dry for a minimum of 2 hours @ 20°C prior to overcoating.

Surface Preparation Steel

• Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard.
• All dust and grease shall be removed prior to coating application.
• If a delay is likely to occur between blasting and application then it is recommended that a coat of CPR 410 – Metal Primer – Epoxy WB is applied as holding primer to obviate flash rusting.

Mixing

• Pour the contents of the CURING AGENT container into the BASE container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved.

Application

• Apply by brush, or roller at a nominal rate of 0.25 to 0.3kg/m².
• After a minimum of 4 hours and before a maximum of 24 hours, apply a second coat at the same rate.
• Should a non-slip finish be required, then broadcast an appropriate Quartz or other aggregate immediately after the first coat.
• Allow to cure.
• Brush off excess aggregate immediately prior to applying the second coat.

Curing

• Allow to cure for a minimum of 4 hours @ 20°C prior to light foot traffic access and 10 hours @ 20° prior to vehicular trafficking.
• 3 days cure @ 20°C is recommended prior to exposure to chemicals.
• Lower temperatures will extend the curing time.

Equipment Cleaning

• Clean equipment with CPR 201 – Tool Clean Solvent prior to curing of the coating.

Limitations

• Do not apply to wet or uncured concrete surfaces.
• Do not apply at temperatures of 3°C or less.

Coverage

• A 5kg pack is sufficient to treat 8.3-10.0 m2 of surface with the recommended two coat treatment, providing an overall d.f.t. of 400-450 microns.

Technical Data

• Pot life @ 20C: 25 Minutes @ 10C: 50 Minutes
• Colours: Grey, Red (BS4800 or RAL colours available on request)
• Coverage: 0.25-0.30kg/m²/coat
• Tack free time @ 20°C: 2 hours
• Hard dry time @ 20°C: 4 hours
• Full chemical resistance @ 20°C: 3 days
• Adhesion strength to concrete: 3.9 MPa (concrete failure)
• Adhesion strength to mild steel: >12 MPa

Chemical Resistance

• Excellent resistance to dilute acids, dilute alkalis, oil, petrol, diesel, vegetable oils.
• Please consult our Technical Department for specific advice.
• All products shall be applied strictly in accordance with the manufacturer’s instructions.

Shelf Life

• Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C.
• CPR 804 – Industrial Floor Paint – Epoxy HB – Rapid Cure has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions.

Packaging

• CPR 804 – Industrial Floor Paint – Epoxy HB – Rapid Cure is supplied in 5kg and 15kg packs

Safety Precautions

• Avoid contact of the material with skin and eyes.
• Wear gloves and goggles.
• Wash off splashes immediately with soap and water.
• Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought.
• Please refer to Material Safety Data Sheet for additional information.

Legal Notice

Whilst all reasonable care is taken in compiling technical data on the Company’s products, all recommendations or suggestions regarding the use of such products are made without guarantee, since the conditions of use are beyond the control of the Company.

It is the customer’s responsibility to satisfy himself that each product is fit for the purpose for which he intends to use it, that the actual conditions of use are suitable and that in the light of our continual research and development program the information relating to each product has not been superseded.