CPR 810 – Industrial Floor Paint – Epoxy WB

Typical Uses

  • CPR 810 – Industrial Floor Paint – Epoxy WB is typically used a floor covering in industrial settings such as food factories, abattoirs, dairies, laboratories etc.
  • As an anti-graffiti coating also can be used as an hygienic, easily cleanable surface on walls, ceilings etc.
  • Full range of Ral & BS colours are available upon request.

£90.00£240.00 Excl VAT

In Stock
Clear
SKU: CPR 810 Categories: ,

Description

Industrial Floor Paint – Epoxy WB

CPR 810 Industrial Floor Paint – Epoxy WB is a high performance, water dispersible Epoxy coating for the treatment of floors and walls in industrial environments. It is designed to be user and environmentally  friendly, containing no  solvents and being of a very low odour during application. CPR 810 – Industrial Floor Paint – Epoxy WB may be easily applied by brush, roller or airless spray, to provide a decorative, abrasion and chemically resistant coating of excellent durability.

Typical Properties

  • May be applied to dry or damp surfaces
  • Available in a range of colours
  • Low odour
  • Easily applied
  • Excellent resistance to water, oils, skydrol, petrol, dilute acids, alkalis and many solvents.
  • Very good adhesion to concrete
  • Hygienic and easily cleaned.
  • Matt and Gloss options
  • Slip resistant options

Direction For Use

Surface Preparations

  • Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%.
  • Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, existing paint finishes, etc.
  • Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. CPR 702 Epoxy Bonding Adhesive
  • Suitable technical treatment, such as vacuum grit blasting, is recommended to ensure a clean, uncontaminated substrate.

Mixing

  • Pour the contents of the BASE container into the CURING AGENT container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved.
  • The mixed material may be thinned by the addition of up to a maximum of 10% by volume of clean, potable water.

Application

  • Apply by brush, roller or airless spray at a nominal rate of 0.20 to 0.25kg/sq.m. per coat equivalent to a dry film thickness of 100-125 microns.
  • A minimum two coat treatment is recommended, applying subsequent coats after a minimum interval of 16 hours curing.
  • Ensure good ventilation after application, as this speeds up the physical drying stage of the curing process.
  • Should a non-slip finish be required, a suitable Quartz should be scattered onto the first coat of CPR 810 –Industrial Floor Paint – Epoxy WB
    whilst still wet.
  • The following day any excess sand may be swept from the surface using a clean brush prior to application of the second coat.
  • Alternatively, for a lightly textured floor finish the coating can be supplied with CPR 206 – Anti-Slip Aggregate pre-incorporated.

Curing

  • Allow to cure for a minimum of 24 hours @ 20°C prior to light foot traffic
  • 48 hours @ 20° prior to vehicular trafficking.
  • 7 days cure @ 20°C is recommended prior to exposure to chemicals.
  • Good ventilation is essential for satisfactory curing of the coating.
  • Lower temperatures will extend the curing time

Equipment Cleaning

Limitations

  • Do not apply to wet or uncured concrete surfaces.
  • Do not apply at temperatures of 3°C or less.
  • In poorly ventilated areas forced extraction must be provided.

Coverage

  • A 5kg pack is sufficient to treat 10.0-12.5 m2 of surface with the recommended two coat treatment, providing an overall d.f.t. of 200-250 microns. (15kg pack pro rata).

Technical Data

  • Pot life @ 20C: 90 Minutes @ 10C: 150 Minutes
  • Colours: Grey, Red (BS4800 or RAL colours on request)
  • Application Temperatures minimum = 3°C maximum = 30°C
  • Coverage: 0.20-0.25kg/m²/coat
  • Volume Solids: 65%
  • Temperature resistance: 75°C (dry), 65°C(wet)

Chemical resistance

  • Chemical resistance: excellent resistance to water, dilute acids, dilute alkalis, glycol ethers, dibasic ester solvent, skydrol, etc.
  • Please consult our Technical Team for specific advice.
  • All products shall be applied strictly in accordance with the manufacturer’s instructions.

Shelf Life

  • Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C.
  • CPR 810 –Industrial Floor Paint – Epoxy WB has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions.

Packaging

  • CPR 810 –Industrial Floor Paint – Epoxy WB is supplied in 5kg and 15kg packs

Safety Precautions

  • Avoid contact of the material with skin and eyes.
  • Wear gloves and goggles
  • Wash off splashes immediately with soap and water.
  • Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought.
  • Please refer to Material Safety Data Sheet for additional information.

Legal Notice

Whilst all reasonable care is taken in compiling technical data on the Company’s products, all recommendations or suggestions regarding the use of such products are made without guarantee, since the conditions of use are beyond the control of the Company.

It is the customer’s responsibility to satisfy himself that each product is fit for the purpose for which he intends to use it, that the actual conditions of use are suitable and that in the light of our continual research and development program the information relating to each product has not been superseded.

Additional information

Weight N/A
size

15kg, 5kg

CPRL Colours

Black (RAL 9005), Carmine Red (RAL 3002), Iron Grey ( RAL 7011), Leaf Green ( RAL 6002), Light Grey (RAL 7035), Oxide Red (Ral 3009), Signal White (RAL 9003), Silver Grey (Ral 7001), Sky Blue (RAL 5015)

Brand

CPRL

Reviews

There are no reviews yet.

Be the first to review “CPR 810 – Industrial Floor Paint – Epoxy WB”

Your email address will not be published.