Fosroc Lokfix S25 – 2.5ltr

Uses

Lokfix S25 is used for anchoring of steel bars into concrete, brickwork, masonry and rock. Recommended applications include:

  • Installation of starter bars
  • Base plate bolts
  • MOT Bolts
  • Installation of balustrades
  • Installation of barriers and safety fences
  • Installation of tie bars

PLEASE CALL FOR UP TO DATE PRICES

In Stock
SKU: Fosroc/Lokfix/2.5ltr Categories: ,

Description

Fosroc – Lokfix S25 (2.5ltr)

Description

Polyester resin anchoring grout meeting requirements of BS EN 1504-6: Anchoring of reinforced steel bars.

Lokfix S25 is a two component polyester anchoring grout supplied in pre-measured quantities. The material cures quickly to give consistent, high performance anchorages. It is a pourable grade, with a 25 minute gel time at 20°C for use in vertical down holes where the hole is 8 to 40 mm greater in diameter than the bar.

Advantages

  • Easy to mix and apply
  • Rapid strength gain
  • Vibration resistant
  • Corrosion resistant
  • Non-expansive
  • Can be placed underwater
  • Increased flowability

Instructions for Use

Hole preparation and formation Optimum performance of Lokfix S25 requires rough sided, dust-free holes. Use of rotary percussive drills with air or water flushing is recommended.

Diamond drilled holes should be under-seamed or the surface roughened with a drill steel. Cast holes should preferably be of inverse dovetail configuration. If parallel sided holes are cast they should be rough to provide adequate keying.

Bar preparation

All bars should be deformed. They should preferably be degreased and all flaky rust removed.

Mixing

A complete pack of resin and catalysed filler should be mixed in one operation. Mixing may be carried out manually or mechanically. When a smooth, even consistency is achieved the grout is ready for use and should be placed well within the gel time of the grout.

Packs have been designed to produce practical and economic volumes of grout.

DO NOT attempt to mix partial pack components.

Installation

Lokfix S25 – Using the calculated volume of grout based on the estimating guide table, the grout should be poured steadily into the prepared holes. The anchor bar is then pressed into the hole to the required depth; slight agitation will assist in achieving a complete bond. The bar should be left undisturbed in the required position until the resin is set.

Cleaning

Any mixing drums, pumps, etc., should be cleaned with Fosroc Solvent 105 within he pot life of the grout. Cured material can only be removed mechanically.

Supply

The pack consists of a can of resin and a plastic bag of hardener contained in a plastic mixing pail with a snap-on lid. Volume of mixed components: 2.5 litres.

Storage

Store in accordance with the Highly Flammable Liquids and Liquefied Petroleum Gases Regulations 1972. Shelf life of 12 months at 20°C will be reduced at higher temperatures.

Limitations

Fire resistance – Resin anchors should not be used where structural load bearing performance has to be maintained in anchors subjected to fire conditions. 

Health and Safety

For further information see appropriate Product Safety Data Sheet.

Fire – Lokfix S25 and Fosroc Solvent 105 are flammable. Do not expose to naked flames or other sources of ignition. No  Smoking. Containers should be tightly sealed when not in use. In the event of fire, extinguish with CO2 or foam.

See below for full product data sheet

Additional information

Brand

Fosroc

Volume

2.5L

Reviews

There are no reviews yet.

Be the first to review “Fosroc Lokfix S25 – 2.5ltr”

Your email address will not be published.

You may also like…

  • Webertec Anchor Grout
    Concrete Crack & Joint Repair

    Webertec Anchor Grout 14.3kg

    Webertec Anchor Grout 14.3kg

    The product is a fast-set polyester resin compound typically used for anchoring and fixing.

    Minimum order quantity is 4 which qualifies for free delivery.

    THIS PRODUCT HAS AN EXTENDED DELIVERY LEAD TIME OF UP TO 15 DAYS.

    PLEASE CALL FOR UP TO DATE PRICES

    (0 reviews)